Knitted Wire Mesh Gasket

Knitted Wire Mesh Gasket

Knitted Wire Mesh Gaskets 1200

Universal EMC gasket to shield lower frequencies

The Knitted wire mesh EMI/RFI shielding gaskets of the 1200 series consist of a layer of knitted electrically conductive metal wires attached to a low-closure force rubber or elastomer core. For heavy-duty applications like EMP or high temperatures, a full metal version is available. Sometimes a Metal knit EMI/RFI gasket is combined with an environmental seal to provide IP rating, depending on the materials used.

Knitted wire mesh gaskets provide a cost-effective solution to high shielding performance applications in the magnetic and electrical fields, including EMP. The gaskets can be made either completely from knitted metal mesh or from knitted metal mesh over an elastomer core which allows recovery after compression.

For high-frequency shielding, foil-based gaskets like Amucor Shield 6800 series will perform better, because of their much larger contact surface.


  • High attenuation for lower frequencies (low-frequency magnetic shielding)
  • Suitable for use under extreme conditions (military applications)
  • Wear-resistant
  • Not susceptible to corrosion
  • Various conductive materials against tension corrosion
  • Roll lengths of 1 to 1000 meters (depending on width and height of the gasket)
  • Tools required: pair of scissors

Options (on request)

  • Customization per customer’s specification
  • Available with flame-retardant core
  • Available with conductive self-adhesive
  • Available with chemical-resistant rubbers like EPDM
  • Silicone sponge for high temperatures up to 220 °C
  • Cut into accurate lengths as a ready-made frame



Knitted wire mesh gasket vs. Amucor shield

Contact points of Amucor shield

Contact points of Knitted wire mesh gasket

Knitted wire mesh gasket groove

Knitted wire mesh EMI/RFI gasket in a groove

metal knit gasket with water sealKnitted wire mesh EMI/RFI gasket combined with water seal

metal knit gasket water seal

Knitted wire mesh EMI/RFI gasket combined with water seal



Stock dimensions

Below are all the standard sizes we keep in stock and so are available quickly. Almost any size and combination can be produced. If you need a size that is not listed below please contact for the options and delivery time.

Round (R)

Knitted wire mesh gasket round technical drawing

Double round (DR)

Knitted wire mesh gasket double round technical drawing

Round with tail (T)

Rectangular (S)

Shielding performance*

Inhouse knitted wire mesh production video

Technical specifications

Per QQ-N-281
BS 3075 N A 13
Class A
diameter 0.11mm
The most commonly used material.
Insensitive to corrosion and neutral on the galvanic scale.
AMS 4187
BS 1475 5056A
Alloy 5056
diameter 0.13mm
Used in some cases for aluminum enclosures.
Aluminum can be chromed with an Al-chrome 1200 layer, if necessary.
Steel core (57%)
Copper cladding (40%)
Tin plating (3%)
diameter 0.11mm
Excellent magnetic as well as electrical properties, because a Ferro alloy is covered with copper.
The outside is tinned to prevent corrosion.
Stainless steel
AISI 304
diameter 0.13mm
The strongest material with shielding performance comparable to aluminum. Highly wear-resistant.

With water seal/IP seal

All knitted mesh EMI/RFI gaskets can be produced with a water seal/IP seal.

The standard material for the fluid seal/water seal is Neoprene which can be adhesive-backed (indicated in red in the drawings) for easy installation. Alternatively, a silicone sponge is also available.


Optimum compression/density

The maximum deflection with a sponge elastomer core is approximately 30%, with hollow extrusion 50%. This is why the hollow type is used more often. Compression levels are important in applications such as liquid filtration and noise attenuation, where flow resistance is critical.



Used to seal enclosure lids and doors, removable cover plates and interface gaskets for EMI shielded vent panels and EMI/RFI shielded windows.


Temperature resistance:

Temperature resistance depends on the core material of the metal knit EMI/RFI gasket. Ranges from -60 °C up to 220 °C is possible. These Metal knit EMI/RFI gaskets are insensitive to external influences and can withstand harsh operating condition very well.

1250 – Knitted wire mesh washers & disks

We also supply knitted wire mesh rings/washers for seals around bolt holes. The rings can be delivered separately but can also be placed in a gasket around bolt holes for better electromagnetic sealing around bolt holes.

For more information about washers and disks check out our knitted wire mesh washers & disks page.

Get a Quotation

Fill in the form below