EMC Dust Filter Ventilation Panels

EMC dust filter ventilation panels

 EMC Dust Filter Ventilation Panel 9510

Products for shielding openings of heating and ventilation systems against undesirable electromagnetic waves. Electronic enclosures where air flow is required for cooling and ventilation but where EMC compliance and dust filtration is critical.

Our EMC dust filter ventilation panels consist of several layers of Aluminum foil mesh encased in a rigid Aluminum frame, pre-drilled, or with fasteners made to the customer’s specifications, or with flow-drilled thread holes.

Approximately 95% of the 9510 series EMC Dust filter ventilation panels are made to customer specifications in compliance with the order. These panels can be treated with a variety of finishes to provide corrosion protection. Air filter oil can be applied to the Aluminum filter to assist control dirt and dust retention.

By default, frames can be provided with an additional 6800 series Amucor or 7000 series Standard shield EMI gasket.

Standard delivery time

Most standard-sized EMC dust filters (see table below) are available from stock. Where not in stock or when you need a custom-made filter, delivery can be  several weeks.

Applications:
  • Electronics enclosures
  • Air conditioning units
  • Fan housings
  • EMC racks
Advantages:
  • Light weight
  • High shielding performance
  • Very low air-flow resistance
  • Reduction of turbulence

9510 series EMC Dust filter ventilation panel 300 x 300 mm with Frame type A, front view

9510 series EMC Dust filter ventilation panel 300 x 300 mm with Frame type A, rear view with EMI- shielding gasket

9510 series EMC Dust filter ventilation panel

Attenuation levels (dB)
FrequencydB
0.01 MHz31
0.1 MHz49
1.0 MHz67
10.0 MHz116
100 MHz109
1000 MHz72
10000 MHz42
Standard dimensions:

Our EMC dust filter ventilation panels are usually custom made for each client. We also have some basic panels available in stock. In the table of standard dimensions below some of our basic panels of EMC dust filter ventilation panels are specified to illustrate the required information. Hole diameter P is 3.5 mm by default, with other dimensions are possible on request. Also available with screw apertures or inserts.

EMC dust filter ventilation panels, technical drawing

Outer dimensionsMounting holes horizontalMounting holes vertical
ABnoDEnoFG
1507524070137.5
100100150150
20010032080150
12512522085162.5
25012533095162.51
150150225100225100
30015043080225100
1751752409524095
3501754409024095
2002003208032080
4002005308532080
2502503309533095
3003004308043080
6003007309043080
Frame options
Frame A
Frame B
Air-flow pressure reduction
9510 series – Air flow pressure drop graph
9510 – EMC Dust filter ventilation panel
◼9500 – Honeycomb ventilation panel (1 layer 3.2 cell x 6.35 mm thick honeycomb)
9500 – Honeycomb ventilation panel (2 layers 3.2 cell x 3.2 mm thick honeycomb)
9500 – Honeycomb ventilation panel (1 layer 1.6 cell x 6.35 mm thick honeycomb)
9500 – Honeycomb ventilation panel (1 layer 3.2 cell x 12.7 mm thick honeycomb)
9500 – Honeycomb ventilation panel (1 layer 3.2 cell x 6.35 mm thick honeycomb + 1 layer 30° slant 3.2 cell x 6.35 mm thick honeycomb for outdoor use)
9500 – Honeycomb ventilation panel (1 layer 3.2 cell x 6.35 mm thick honeycomb + 1 layer 45° slant 3.2 cell x 6.35 mm thick honeycomb for outdoor use)
9500 – Honeycomb ventilation panel (1 layer 3.2 cell x 6.35 mm thick honeycomb + 1 layer 60° slant 3.2 cell x 6.35 mm thick honeycomb for outdoor use)

Please note : These values are measured under laboratory conditions. Results may vary in other situations; Please read our Guarantee.

Get a Quotation

Fill in the form below