Skip to content
JHSC Home / Products / Holland Shielding Home / Amucor Tape
Amucor foil and tape for EMI shielding. Amucor foil or tape can be used to shield plastic housings and enclosures.
Many EMI problems can be solved easily by the use of Amucor foil or tape, a commonly used material. Amucor foil and tape can be produced with or without (conductive) self-adhesive and an optional insulation layer.
Amucor tape can be cut to any width starting at 3 mm and can be delivered from stock. The most commonly used width is 25 mm; the standard roll length is 16.5 meters.
If coverage of large surfaces is needed, it is usually best to use tape with a conductive self-adhesive in combination with foil. This solution is much cheaper than only using tape.
Amucor foil can also be delivered as die-cut, according to the customer’s drawing, on a strip or in pieces (stickers), with optional self-adhesive.
Amucor foil for EMI/RFI shielding
We can cut all our EMI/RFI-shielding tapes to any specific width
Amucor foil roll for EMI/RFI shielding
With our automated CNC cutting system we can cut Amucor foil in large quantities and according to the client’s CAD drawing
The reinforced Amucor foil is both cost effective and heat resistant. This thin foil can be applied easily to any surface and any shape of housing. We can also supply the foil, which is 0.04 mm thick, in a die-cut version.
4701 – Amucor foil, technical drawing
This is an Amucor tape (type of aluminium) that is 11 microns thick, reinforced with polyester (23 microns thick) and with an acrylic adhesive on the back.
4702 – Amucor tape with standard adhesive, technical drawing
Amucor foil + PET film + Amucor foil. This product consists of two layers of 11-micron thick Amucor (type of aluminium) with a 23-micron layer of polyester in between. This material is extremely strong.
4716 – Amucor tape with PET in the middle, technical drawing
Amucor foil can also be produced with a strengthening reinforcement net. Because the reinforcement net makes this material so strong, it can be produced in a very large width of 3100 mm. This material is designed to cover walls and floors for protection against unwanted radio frequencies (RF). The material can also be used to quickly create a shielded room, for example by covering the walls of a wooden box. Please note: at the top of the metal is a thin insulation layer for protection against corrosion.
Amucor foil with a reinforcement net can be produced as a foil (4706) without self-adhesive but is also available as tape (4707), with standard adhesive.
4706 – Amucor foil with reinforcement net, technical drawing
4706 – Amucor foil with reinforcement net
For more information:
Sandwich tape consisting of two layers of Amucor (11 microns thick) with polyester (23 microns thick) in between and a conductive adhesive on the back.
4718 – Amucor tape with PET in the middle and conductive adhesive, technical drawing
In the table below you will find the shielding characteristics of Amucor foil.
There are many factors that influence the actual effectiveness of an EMI/RFI-shielding tape after it has been applied, such as type and thickness of the foil, type of adhesive, closeness of contact, smoothness of the application surface, strength and frequency of the EMI/RFI signal, etc. Still, a nominal attenuation value can be determined using standard tests and fixtures.
For Amucor tape, typical shielding effectiveness (far field) is in the range of 60 dB to 80 dB (10 KHz to 20 GHz).
For more specifications see the table and graph below.
Field | Frequency | Amucor foil |
---|---|---|
0.04 mm thick | ||
E | 1 MHz | 121 dB |
E | 10 MHz | 110 dB |
E | 100 MHz | 103 dB |
E | 400 MHz | 98 dB |
P | 1 GHz | 92 dB |
P | 10 GHz | 85 dB |
These values are measured under laboratory conditions. In other situations results may differ; please read our Guarantee. |
🟥Mu-copper |
⬛Amucor foil |
🟩Conductive textile |
Please note: These values are measured under laboratory conditions. In other situations, results may differ. Please read our Guarantee.
Part number (Foil without adhesive) | 4701 Max. width 1100 mm | 4716 Max. width 1100 mm | 4706 Max. width 3100 mm |
---|---|---|---|
Part number (Tape with standard adhesive) | 4702 Max. width 1100 mm | 4717 Max. width 1100 mm | 4707 Max. width 1100 mm |
Part number (Tape with conductive adhesive) | – | 4718 Max. width 1100 mm | – |
Part number (Foil with insulation layer (UL94V-0) 0.15 mm (white)) | 4704 Max. width 900 mm | 4719 Max. width 900 mm | 4709 Max. width 900 mm |
Part number (Foil with insulation layer (UL94V-0) 0.22 mm (black)) | 4705 Max. width 1100 mm | 4720 Max. width 1100 mm | 4710 Max. width 1100 mm |
Construction | ![]() | ![]() | ![]() |
Foil material | Amucor | Amucor and PET | Amucor with a reinforcement net |
Surface | bright | bright | bright |
Foil thickness | 0.023 mm | 0.35 mm | – |
Total thickness | 0.048 mm | 0.3725 mm | – |
Adhesive | synthetic conductive resin | synthetic conductive resin | – |
Adhesive performance | 4.5 N/cm | 4.5 N/cm | – |
El. resistance through adhesive | 0.003 Ohm | 0.003 Ohm | 0.003 Ohm |
For tape, standard roll widths (mm) * | 10, 25, 50, 100 | 10, 25, 50, 100 | 10, 25, 50, 100 |
Roll lengths * | Min. 16.5m (standard) Other roll lengths on request | ||
These values are measured under laboratory conditions. In other situations results may differ; please read our Guarantee. |
* Other dimensions on request
Get a quotation
Fill in the form below
© Copyright 2022 Japan Homeland security Corporation. All Rights Reserved.