Standard Shield - Japan Homeland Security Corporation

Standard Shield

Standard Shield 7000 series is an economical HF (High Frequency) EMI shielding gasket which can be supplied in a wide range of dimensions. It is very effective in combination with stainless steel, copper and chrome-plated constructions.

Our 7000 series Standard shield EMI gaskets can be provided with a conductive or a non-conductive self-adhesive strip on the back for easy assembly.

Standard shield consists of a foam core covered with highly electrically conductive textile. The following foam cores can be chosen:

Neoprene foam core (foam code N)
EPDM foam core (foam code E)
Low closure force PVC foam (foam code P)
Flame retardant UL94V-0 foam (foam code F)

For smaller widths than 3 mm we suggest to use the conductive adhesive (code 03). This guarantees excellent EMI/RFI shielding performance.

Please note: For special application different foam cores, conductive foils and fabrics are available on request.

Tape Specification

01 Standard self-adhesive placed in the middle
02 Without self-adhesive
03 With conductive self-adhesive (only recommended on small sizes)
06 Standard self-adhesive, asymmetrical
07 Standard self-adhesive placed on the side

Tape Specification

N : Standard Neoprene Foam
E : EPDM foam core
P Low closure force PVC Foam, slow recovery
F Flame retardant Foam (UL94V-0)

Benefits

Self-adhesive EMC gasket
Easy to fit, can be cut with scissors
Gasket can be die-cut (screw-holes, bites for easy bending etc.)
Roll length of 1 to 1000 meters (Depending on width and height of the EMI gasket)
High EMI/RFI shielding performance
Low closure force
EXTREMELY STRONG
Deflection 50%

Options

N : Standard Neoprene Foam
E : EPDM foam core
P Low closure force PVC Foam, slow recovery
F Flame retardant Foam (UL94V-0)

Standard dimensions

Width X (mm)
Height Y(mm)		2	3	4	5	6	7	8	9	10	12	15	18	20	25	32	50
	1	7021	7031	7041	7051	7061	7071	7081	7091	70101	70121	70151	70181	70201	70251	70321	70501
	2	7022	7032	7042	7052	7062	7072	7082	7092	70102	70122	70152	70182	70202	70252	70322	70502
	3		7033	7043	7053	7063	7073	7083	7093	70103	70123	70153	70183	70203	70253	70323	70503
	4			7044	7054	7064	7074	7084	7094	70104	70124	70154	70184	70204	70254	70324	70504
	5				7055	7065	7075	7085	7095	70105	70125	70155	70185	70205	70255	70325	70505
	6					7066	7076	7086	7096	70106	70126	70156	70186	70206	70256	70326	70506
	8						7078	7088	7098	70108	70128	70158	70188	70208	70258	70328	70508
	9								7099	70109	70129	70159	70189	70209	70259	70329	70509
	10									701010	701210	701510	701810	702010	702510	703210	705010
	12										701212	701512	701812	702012	702512	703212	705012

Shielding performance

Mechanical properties

Please note : These values are measured under laboratory conditions. Results may vary in other situations; please read our Guarantee.

High temperature version

The standard neoprene foam core can withstand temperatures up to 85 °C. If you have an application where a higher maximum temperature is required we can deliver the same type of EMI gasket with a FUBA foam core which also has a high deflection up to 65 %. This FUBA foam can withstand temperatures up to 220 °C. When your application requires an even higher temperature, we can deliver this type of gasket with silicone foam core on request.

Stamped out patterns can be carried out on request

Optionally, these EMI gaskets can be provided with bites, cuts, holes or other patterns. These cut-outs/patterns may be used for easy bending or easy assembly of the EMI gasket.